CMC
Pro Series Rescue Harness
CMC Pro Series Rescue
Harness |
This is an exceptionally comfortable harness. Built to meet NFPA and ANSI standards. The CMC Pro Series Rescue Harness has the durable construction demanded by rescue professionals. The waist and leg loops are made from three-inch(7.7cm) web. They are backed by a full four inches(10.3cm) of closed cell foam padding, protected by Cordura nylon. Quick fit buckles at the waist and legs allow fast adjustment. This harness also has buckles on the side straps to allow an even wider range of comfort fitting adjustment. Color: black (red colored padding is available by special order).
Catalog # |
Size |
Waist |
Leg |
Weight |
202282 |
Small |
26”-30”(67-77cm) |
18”-26”(46-67cm) |
3.3 lbs.(1.5kg) |
202283 |
Medium |
30”-34”(77-87cm) |
20”-28”(51-72cm) |
3.4 lbs.(1.5kg) |
202284 |
Large |
34”-38”(87-97cm) |
22”-30”(56-77cm) |
3.5 lbs.(1.6kg) |
202285 |
X-Large |
38”-42”(97-108cm) |
22”-30”(56-77cm) |
3.75 lbs.(1.7kg) |
202286 |
XX-Large |
42”-46”(108-118cm) |
24”-32”(62-82cm) |
4 lbs.(1.8kg) |
CMC
Pro Series Chest Harness
CMC Pro
Series Chest Harness |
A Chest Harness that attaches to the Pro Series Rescue Harness. The front strap effectively transfers the weight to the waist D-ring, maintaining nearly the same level of comfort that the Pro Series harnesses are known for. Front, sides and back are padded to maximize comfort when lifting from the oversized back D-ring. Color: black (red colored padding is available by special order). Weight 3 lbs.(1.4kg).
Catalog #202355 CMC Pro Series Chest Harness
CMC
Pro Series Spreader Bar
CMC Spreader
Bar |
The CMC Pro Series Spreader Bar gives you more working room in situations with low ceiling clearance. Adjustment buckles at the shoulder allow the wearer to balance the lifting for the most comfort. The spreader bar uses anodized aluminum plate, CMC Pro Series webbing and U.S. Forgecraft Buckles. Color: blue with black webbing. Weight 1.8 lbs.(.8kg).
Catalog #202200 CMC Pro Series Spreader Bar
CMC
Rescue Pro Pocket
Hang the Pro Pocket from your rescue harness to store
runners, safety scissors, gloves and other equipment. The main bag is large
enough to fit your hand inside and can be used to store bulky items. The front
pocket is the place to keep things you do not want in your pants pocket, but do
not want to drop either, like your keys or pager. The small front pocket will
hold your scissors or safety knife. The carabiner
loops allow you to clip off runners to the outside of the bag or to put a
safety tether on any tools you might be using. Two webbing straps wrap around
your harness and adjust through a plastic keeper allowing a tight, stable fit
for most harnesses. Made of 1000 denier Cordura nylon.
Color: black. Size: 6” x 4” x 11”(15x10x28cm). Made in
Catalog #434105 CMC Rescue Pro Pocket
CMC
Pro Series Confined Space Rescue Harness
CMC Confined Space Rescue
Harness |
Designed to meet the needs of confined space rescue teams, the CMC Pro Series Confined Space Rescue Harness is an excellent choice for most industrial rescue operations. The design, which was tested and refined in CMC’s confined space training courses, combines the outstanding performance of CMC harnesses with the special requirements of industrial or confined space rescue. Quick-fit buckles allow the harness to be put on quickly over other response gear. The unique design of the shoulder lifting points transfer the weight effectively to the legs. The mid-back lifting point features an extra large D-ring. The front and rear D-rings are the same as on the CMC Pro Series Rescue Harness. Waist and legs are three inch(7.7cm) web with four inches(10.3cm) of closed cell foam padding. Color: black webbing with blue vest and padding.
Catalog # |
Size |
Waist |
Leg |
Weight |
202202 |
Small |
26”-30”(67-77cm) |
18”-26”(46-67cm) |
7 lbs.(3.2kg) |
202203 |
Medium |
30”-34”(77-87cm) |
20”-28”(51-72cm) |
7.5 lbs.(3.4kg) |
202204 |
Large |
34”-38”(87-97cm) |
22”-30”(56-77cm) |
8 lbs.(3.6kg) |
202205 |
X-Large |
38”-42”(97-108cm) |
22”-30”(56-77cm) |
8.5 lbs.(3.9kg) |
202206 |
XX-Large |
42”-46”(108-118cm) |
24”-32”(62-82cm) |
9 lbs.(4.1kg) |
CMC
Rescue Utility Harness
Built to meet the physical and
testing specifications required by NFPA Standard 1983 (1990 Edition). Made from
1.75”(4.5cm) webbing with a 9000 lb.(4090kg) test
strength. Front D ring attachment point. Universal adjustable
fit. An excellent choice for the engine or truck
company’s rope kit. Color: black. Weight 1.7 lbs.(.8kg).
Made in
Catalog #202306 CMC Rescue Utility Harness
CMC
Pro Series Lifesaver™ Victim Harness
Designed by Rick Homan of the Montrose
SAR Team and field tested by several
Catalog #202403 Lifesaver™ Victim Harness
Other CMC products are available. Please call or write for a prompt quotation.
Roco
Rescue Plus Series Seat & Chest Harness
The #R112 is a heavy-duty, Class II padded seat harness for
the industrial rescuer. Constructed primarily of 2 inch(5cm)
black flat webbing, the seat is fully adjustable, and the leg loops are made of
3 inch(7.6cm) webbing for comfort. Has large D-ring for front attachment, and
sewn webbing loop in the back for hanging gear and trailing lines. Mil-spec hardware. The #R113 is the companion chest harness
which mates with the #R112 with a simple two-point connection, creating a Class
III full body harness, now widely used for confined space rescue work. The Roco Seat & Chest Harnesses have been UL tested and
meet all requirements of NFPA 1983-1990, and are so labeled. D-rings rated at
5000 lbs.(2268kg). 2”(5cm)
flat webbing rated at 9500 lbs.(4309kg). Total tensile strength is 5000 lbs.(2268kg). Back-up safety loop rated at over 6000 lbs.(2722kg) Made in
Catalog # |
Description |
Size |
Measurement |
Weight |
R112 |
Seat Harness |
Standard Large |
Waist: 30”-44”(77-113cm) Waist: 42”-48”(108-123cm) |
3.5 lbs.(1.6kg) |
R113 |
Chest Harness |
Standard Large |
Chest: 30”-48”(77-123cm) Chest: 44”-52”(113-133cm) |
3.1 lbs.(1.4kg) |
Petzl
Fractio Cavers Harness
This new seat harness is designed for cavers and rappellers. It is a combination of a waist belt and leg
loops. The leg loops attach near the articulation of the hips yielding improved
freedom of movement. This adjustable harness is made in two sizes to guarantee
you a good fit. (See the sizing chart). All stitching is protected from
abrasions. Made of two independent lengths of webbing.
This harness will not fall down while you are walking around. Weight 19oz.(545g). Made in
Catalog #C16 Fractio Cavers
Catalog #C16/100 Protection for Fractio
Petzl
Super Avanti Caving Harness
One size fits most. This very lightweight harness may be
used in combination with the Petzl C18 or C26 chest
harness. Waist adjusts from 21”(55cm) to 39”(l00cm).
The thigh adjusts from 18.5”(47cm) to 27.5”(70cm).
Weight 11.3oz.(320g). Made in
Catalog #C12 Super Avanti
SIZE CHART FOR FRACTIO AND SUPER AVANTI HARNESSES
|
A |
B |
Minimum |
21.5”(55.1cm) |
18.5”(47.4cm) |
Maximum |
27”(69.2cm) |
27.5”(70.5cm) |
Petzl
Caving Chest |
Figure 8 Chest |
Voltige Chest |
Chest Harnesses
Catalog #C60 Voltige Chest Harness
Catalog #C07 Classic Chest Harness(chest w/two shoulder straps)
Catalog #C18 Figure 8 Chest Harness
Catalog #C26 Chest Harness for Cavers
Petzl
Chouca Rock Climbers Harness
Petzl Chouca |
This one size fits all harness features a waist belt and leg
loop combination for a high degree of comfort. The belt has padding which
protects in a fall, prevents chafing from gear hung on gear loops and is
comfortable on steep or overhanging pitches. Includes four gear loops. Belt and
leg loops are adjustable. The C23 fits waists up to 38”(101cm).
The new C23-XL fits 40” to 46”(107-117cm) waists. A
matching C60 chest harness is available. Weight 21oz.(575g).
Made in
Catalog #C23 Chouca Seat Harness
Catalog #C23‑XL X‑Large Chouca Seat Harness
Petzl
Gourou Rock Climbers Harness
This is Petzl’s finest lightweight
harness. It is adjustable, with one size fitting most. Padded waist belt and
leg loops. Has four gear loops. One harness fits waist sizes from 27” to 40”(69-102cm). Matching C60 chest harness is available. Weight
1 lb.(450g). Made in
Catalog #C27 Gourou
Petzl
Ankle Harness
Here’s one for the stunt men and
thrill seekers out there. Ankle harness set with straps for connection to a
bungee system. Used by “bungee jumpers”. Weight 2.2 lbs.(1kg).
Made in
Catalog #C84 Ankle Harness
Petzl
Adrenaline and Intervention
Rock Climbing Seat Harness
Petzl Adrenaline &
Intervention |
Technically
advanced free climbing harness with padded leg loops and belt. Easy to put on with fast clip nylon waist buckle. Four gear
loops, and the elasticized butt straps keep leg loops in place. Fluorescent
colors. Matching C60 chest harness is available. The intervention is the same
harness but all black for police and tactical uses. Average weight 16oz.(457g). Made in
Catalog #C22‑X Adrenaline Seat Harness(replace X w/your size)
Catalog #C28‑X Intervention Seat Harness(replace X w/your size)
(See sizing following
chart)
Petzl
Jump Rock Climbers Seat Harness
New free climbing harness with fully padded waist belt and
leg loops. Ultra‑lightweight while retaining good
comfort, protection and freedom of movement. Has three gear loops. Matching
C60 chest harness is available. Fluorescent colors. Average weight 15.5oz.(436g). Made in
Catalog #C20‑X Jump Seat Harness(replace X w/your size)
XS = Extra Small S = Small M = Medium L = Large XL = Extra Large
Sizing
for Petzl Jump(C20),
Adrenaline(C22) and Mercury(C31) Harnesses:
A |
B |
Size |
27.5”(70.5cm) |
19.5”(50cm) |
XS |
29.5”(75.5cm) |
21.5”(55cm) |
S |
31.5”(81cm) |
21.5”(55cm) |
M |
33.5”(86cm) |
23.5”(60cm) |
L |
35.5”(91cm) |
25.5”(65.5cm) |
XL |
Petzl
Mercury Rock Climber’s Seat Harness
Petzl Mercury |
This is Petzl’s most economical climbers seat harness. It has the same design and features
as the Jump, but with thinner webbing and two racking loops. Average weight is
15oz.(420g). Made in
Catalog #C31-X Mercury Seat Harness(replace X w/your size)
XS = Extra Small S = Small M = Medium L = Large XL = Extra Large
(See previous sizing
chart)
Petzl
Crux and Papion Rock Climber’s Seat Harness
Petzl Crux |
A lightweight free climbing harness.
The lightest of the lights, super choice for the
weight-conscious climber. Features padded waist and leg loops, fast
clip-in nylon waist buckle and two gear loops. Matching C60 chest harness is
available. Fluorescent colors. Average weight is 10oz.(283g).
Made in
Catalog #C62‑X Crux Seat Harness(replace X w/your size)
Catalog #C62B-X Papion(All Black Crux)(replace X w/your size)
XS = Extra Small S = Small M = Medium L = Large XL = Extra Large
Sizing Petzl Crux(C62, C62B) Harnesses.
A |
B |
Size |
25.5”(65.5cm) |
19.5”(50cm) |
XS |
27.5”(70.5cm) |
19.5”(50cm) |
S |
29.5”(75.5cm) |
21.5”(55cm) |
M |
31.5”(81cm) |
21.5”(55cm) |
L |
33.5”(86cm) |
23.5”(60cm) |
XL |
Petzl
8003 Mountaineer’s Full Body Harness
Petzl Mountaineer’s FBH |
Full body harness for mountaineering and other applications
where it is critical to keep upright when suspended in the harness. UIAA
approved, made from 2”(5cm) wide nylon webbing
[tensile strength 4400 lbs.(1996kg)], with adjusting buckles. Weight 19.4oz.(554g). Made in
Catalog #C05 Standard ‑ fits most adults(chest size up to 37”[95cm])
Catalog #C05‑L Large ‑ fits larger adults(chest size up to 46”[118cm])
Petzl
Ouistiti Child’s Full Body Climbing Harness
Do not leave the kids at home. Take them with you and let them
experience the joy of climbing and rappelling. Children do not have a
pronounced waist, in the event of a upside‑down
fall, they risk falling out of just a seat harness. Petzl’s
solution: The Ouistiti Full Body Harness. Easy to put
on, it adjusts with only two buckles. Fits children from
Sizing: Thigh‑Max = 20”(51cm); Waist‑15.5” to 23.5”(40-60cm). Weight 11oz.(310g).
Catalog #C68‑S Ouistiti Child’s Harness
Petzl
Industrial Harness
A full body harnesses which meet AFNOR S71020 standards for
industrial harnesses. The Light (#C70) incorporates the harness into a jacket,
making it simple to put on without mistakes in 30 seconds or less, even if you
have never seen it before. Features a two point front tie in
and an integral back lifting point on a tether. Weight 2.9 lbs.(1300g). Made in
Catalog #C70 Light
Petzl
Evacuation Triangle |
One‑size‑fits‑all diaper
seat. Quick and simple to put on, perfect for
evacuating people from cliffs, building ledges and roofs. Put it on like
a diaper, clip a locking D carabiner
with rope into the three steel rings. Manufactured to exceed
STRM standards #SU 530/87. Weight 1.5 lbs.(700g).
Made in
Catalog #C80 Evacuation Triangle
Petzl
Dog Harness
Petzl Dog Harness |
A full body harness for SAR dogs. This padded harness
enables you to safely and securely lower your dog down cliffs or from
helicopters. The back pack straps allows one person to
carry a tired or injured animal. One size fits medium to large size animals. Weight
30oz.(870g). Made in
Catalog #C99 Dog Harness
PMI
Hasty Harness
PMI Hasty Harness |
This simple and secure evacuation seat is
specially designed to be lightweight, efficient and easy to put on a patient in
distress. The split center piece of the triangle design conforms to the wearer
and is surprisingly comfortable, even for an extended ride. One size fits most.
Catalog # SG51114 Hasty Harness
PMI
Avatar Full Body Harness
PMI Avatar Harness |
Think you've seen this harness before,
only with a different label? Take another look! The Avatar is a one-of-a-kind
harness with an array of basic design and not-so-subtle features that make it the
most versatile, comfortable, and useful harness you're ever likely to wear!
Black and Safety Yellow. Comes with a convenient carry - storage bag. Made in
Catalog # SG51036 Avatar Full Body HarnessStandard Size
Catalog # SG51042 Avatar Full Body Harness Large- XXL Size
PMI
Circumferential Chest Harness
PMI Circumferential Harness |
An alternate chest harness for the Avatar
Harness. Attaches to any Avatar seat harness. Circumferential design holds
wearer's upper torso closer to the rope than our standard chest harness. Perfect
for rope ascending systems using a chest roller plate. Includes: Dorsal ring,
sternal sewn loop and chest roller mounting system. (Chest roller plate sold
separately)
Catalog # SG51037 Circumferential Chest Harness
PMI
Avatar Seat Harness
Just like your favorite pair of jeans, the
Avatar is extraordinarily wearable. Ergonomic shape, contoured padding,
double-adjustable waist, adjustable leg loops and adjustable rear risers lend
to the comfort of this harness. Front Waist and side D Ring attachment points
make this an excellent choice for work or rescue. Can be retrofitted with your
choice of two optional Chest Harnesses to meet NFPA Class III and ANSI fall
protection standards. Black and Safety Yellow. Comes with a convenient storage-carry
bag. Made in
Catalog # SG51043 Avatar Seat Harness Standard
Catalog # SG41044 Avatar Seat Harness Large- XXL
PMI
Spectrum Harness
A simple yet comfortable and exceptionally
versatile harness design with adjustable waist and leg loops. This harness is
an excellent choice for gyms, schools, or anywhere harnesses are shared among
users. One gear loop. Made in
Catalog # SG51112 Spectrum Harness
PMI
Pit Viper Harness
This caving harness features a low
profile, and very low frontal attachment point, making it an excellent choice
for cave exploration or cave rescue. Designed to work with Frog chest harness.
13/4” flat webbing features abrasion guards over the backs of each leg strap.
Two gear loops. Adjustable waist and legs. Color: Red. Standard: Waist-26”/40”
Legs-18”/28” Large: Waist-30”/51” Legs-21”/31”
Catalog # SG51038 Pit Viper Standard Harness
Catalog # SG51046 Pit Viper Large Harness
PMI
Frog System Chest Harness
Comfort and simplicity in a
one-size-fits-all design. Constructed of 1” (2.5cm) flat webbing with plastic
quick snap buckles. Designed specifically for use in Frog type climbing system to
raise the seat harness mounted ascender as one climbs. Not for use as
conventional chest harness. Color: Black.
Catalog # SG51047 Frog System Chest Harness
PMI
Bucket Belt
Fall prevention waist belt with attached
17 ¾” (45cm) lanyard complete with ¾” (1.2cm) snap hook for attachment to
anchor rings and Ds. This belt is
designed especially for fall prevention of workers in bucket trucks, and should
be rigged appropriately so as to prevent any possibility of a fall. Not intended for fall arrest, or to be used
in a free hanging configuration.
Catalog # SG51123 Bucket Belt
PMI
RIT Class II Seat Harness
A harness designed to be worn over
turnouts. Special design and closure
system allows the harness to be left on your turnouts all the time. Sew the optional Nomex loop kit to your
turnout pants for secure semi-premanent fitting
Catalog # SG51120 RIT Class II Seat Harness
Catalog # SG51124 Nomex
Weinel
Born Body Harness
Born Body Harness |
An all new design full body harness that
meets or exceeds all national standards for industrial and commercial
applications. The Born Body Harness Features a sliding back yoke
assembly to help reduce fall impact forces. The Born Body Harness has both
front and back clip-in-points. Also available with two 5000 lb.(2268kg) mil spec forged steel shoulder D-Rings for
confined space rescue. Closed cell foam padding on the leg loops and lower
chest makes this full body harness a joy to work in. Weight 5 lbs.(2.26kg). Made in
Born Body Harness Size Selection:
|
Small |
Medium |
Large |
X-Large |
Chest |
28”-38” (72-98cm) |
38”-48” (98-123cm) |
48”-58” (123-148cm) |
58”-68” (148-174cm) |
Diaphragm |
22”-34” (57-87cm) |
34”-46” (87-118cm) |
46”-56” (118-144cm) |
56”-66” (144-169cm) |
Catalog #WBBH-X Born Body Harness(replace X w/your size)
Catalog #WBBH-X-SD Born Body Harness w/Shoulder D-Rings(replace X w/your size)
Weinel
Full Body Harness
Weinel Full Body Harness |
A simple to do, comfortable, one size fits all [5’2” to 6’ 4”(159-195cm) tall, 24” to 50”(61.5-128cm) waist] full body
harness. Meets or exceeds NFPA/ANSI Class III standards and is labeled as such.
Made of 1.75”(4.5cm) 9000 lb.(4082kg) solid nylon
webbing, all load bearing hardware is 5000 lb.(2268kg) or more mil spec for
your safety. Front waist level D ring for rappelling and rescue and a high D
ring in the center of the back for lifting or restraining in a vertical lift.
Also available with two 5000 lb.(2268kg) mil spec
forged steel shoulder D-rings for confined space rescue. Weight 4.5 lbs.(2kg). Made in
Catalog #WFBH Weinel Full Body Harness
Catalog #WFBH-SD Weinel Full Body Harness w/Shoulder D-Rings
Weinel
Y Lifting Spreader Yoke
This useful lifting bridle is designed to be used with any
full body harness with shoulder lifting points. Manufactured with one inch(2.56cm) solid 6000 pound(2722kg) nylon webbing. The 16”
x 1.25”(41x3.2cm) spreader bar fits through the
majority of access ways, and is extremely rugged. Overall height 28”(72cm). Weight 37oz.(1kg). Made in
Catalog #WYLSY Y Lifting Yoke
Weinel
Chest Harnesses
Chest Harness |
This chest harness is designed for either front or back line
connection. Front connection point is used in conjunction with a seat harness
in rope rescue and climbing applications. Back connection is used for in‑water
personnel tether during water rescue operations. The harness is easy to don and
fits most people [24” to 48”(61.5-123cm) chest]. Made
of 9000 lb.(4082kg), 1.75”(4.5cm) solid nylon webbing
and 5000 lb.(2268kg) mil spec hardware. Meets or exceeds NFPA and ANSI
standards. Weight 1.5 lbs. (879g). Made in
Catalog #WCH Chest Harness
Catalog #WBJCH Light Weight Recreational Chest Harness
Weinel
Last Chance Belt
Last Chance Belt |
A functional uniform belt. Made of
1.75”(4.5cm) black webbing with a test strength of
9000 lbs.(4090kg). The black hardware is manufactured to military
specifications. One size fits all up to 46”(118cm).
Features a sewn in V ring near the buckle. For an emergency escape, simply flip
open the V ring, clip in a carabiner and a rappel
device then make your descent. Looks
great on your uniform and that way you will be sure to always have it with you.
Weight 12oz.(339g). Made in
WARNING: this item is sold as a belt. It is not to be used for rappelling except under direct threat to your life.
Catalog #WLCB‑1 Last Chance Belt
Catalog #WLCB-1-L Large [fits up to 60”(154cm)] Last Chance Belt
Weinel
Victim Emergency Harness
A 13’(3.9m) length of 2”(50mm) flat
webbing with heavy duty military specification buckle. Webbing minimum test
strength 6000 lbs.(2722kg). Many
practical uses in the field. It makes a fast, secure and comfortable
harness for a victim, a spare harness for the rescuer, and an adjustable swami
belt, or as a stretcher (or backboard) tie‑in strap. Includes
instructions on how to use as a harness and suggestions for other applications.
Every rescue pack should have at least one. Colors: red, blue or black. Weight
12oz.(339g). Made in
Catalog #VEH156‑X Victim Emergency Harness(replace X w/color)
Weinel
Rescue/Ladder Belt
Weinel Rescue/Ladder Belt |
Designed as a ladder belt, it may be worn inside or outside
turnout gear. If worn outside you can even hang tools on it. Meets or exceeds
NFPA‑ANSI requirements for a Class II seat harness. The belt is
constructed of 1.75”(4.5cm) nylon webbing tested to
9000 lbs.(4082kg) or more. This belt is designed to function as a ladder belt,
and it has a butt strap which can be dropped down forming a rappel seat. Includes a leather pad under the waist belt adjuster to prevent
body contact with hard metal adjuster. When used as a ladder belt you
will need an SMC #20001 carabiner. The belt has two
adjustments: one for the waist belt and the other for the buttocks. Weight 17oz.(482g). Made in
Catalog #WRLB‑1 Weinel Rescue/Ladder Belt only
Catalog #WRLB‑2 Weinel Rescue/Ladder Belt with Carabiner
Weinel
NFPA Rescue Seat
Weinel Rappel Rescue Seat |
Designed for
rescue and tactical work. Exceeds ANSI, and NFPA
standards for a Class II seat harness. Manufactured from 1.75”(4.5cm), 9000 lb.(4090kg) nylon webbing and military
specification 5000 lb.(2268kg) hardware. One size fits all waist and leg
loops. Includes a leather pad under the waist belt adjuster
to prevent body contact with hard metal parts. Waist: 21”-55”(53-140cm). Leg loops: 7”-29”(18-74cm).
Weight 26oz.(736g). Made in
5000 lb.(2268kg) D-ring clip in point
Two 5000 lb.(2268kg) D-ring accessory clip in points
NFPA and ANSI Labeled (Except black)
Catalog #WRRS‑O Weinel Rappel/Rescue Seat ‑ Orange
Catalog #WRRS‑B Weinel Rappel/Rescue Seat ‑ Black
Weinel
Ascending Stirrup
Adjustable length foot strap with back‑up
connection to seat harness. Used in
Catalog #WJS Ascending Stirrup
Weinel
Tech Harnesses
Four styles to choose from, a seat harness for every need. Over three years in the making. We looked at every harness that we could (hundreds of them), picking and choosing the best features of each, combining and refining them to the point of perfection. The Tech Series Harnesses all share the following features: 3”(7.6cm) waist belt, elastic butt straps, and single pass 5000 lb.(2268kg) buckles. All webbing and hardware exceeds NFPA standards, and all bear labels certifying compliance with applicable ANSI standards.
Weinel
Tech Harness Sizing
For the highest degree of safety and comfort, a harness must fit properly. The belt on all Tech Seat Harnesses may be lapped on top of itself for smaller people, or a gap of up to 8”(20cm) between the ends of the waist belt may be left to accommodate larger people. Always have at least 4”(10cm) of webbing left after buckling the single pass buckle. Tie the end in an overhand knot after adjusting to fit waist. The harness is oriented properly when the label is on the left leg.
Tech Seat Harness Sizing Chart
|
Small |
Medium |
Large |
Waist |
22” - 30”(56-77cm) |
29” - 37”(74-95cm) |
36” - 44”(92-113cm) |
Thigh |
16” - 22”(41-56cm) |
22” - 28”(56-72cm) |
26” - 32”(67-82cm) |
Weinel
Basic Tech Seat Harness
A lightweight
adjustable seat harness for rappelling and free climbing. Features a
6000 lb.(2722kg) webbing tie in point. No bells and
whistles here, plain and simple. No gear loops or other attachments. Black and orange webbing with plated hardware. Weight 18oz.(500g). Made in
S = Small M = Medium L = Large
Catalog #WBTS‑X Basic Tech Seat Harness(replace X w/your size)
Weinel
Tech Rescue Seat Harness
Tech Rescue Seat |
Features two 5000 lb.(2268kg) mil spec D rings, one as the tie‑in point up
front, and the second as a hauling loop on the back. Four gear loops insure
plenty of space to carry additional items such as chocks, carabiners and
slings. Black and orange webbing with plated hardware.
Exceeds ANSI standards and is labeled as such. Weight 25oz.(707g)
Made in
S = Small M = Medium L = Large
Catalog #WTRS‑X Tech Rescue Seat Harness(replace X w/your size)
Weinel
Padded Tech Rescue and Recreational Seat Harness
Padded Tech Rescue Seat |
The same features as the Tech Rescue Seat Harness with the
added luxury of 3/8”(l0mm) closed cell foam padding on
the waist and leg loops. The padding is covered with a strong abrasion
resistant fabric. The ends of the waist belt and leg loops are anatomically
tapered to offer the highest degree of comfort. Black and
orange webbing, yellow fabric with plated hardware. Exceeds ANSI
standards and is labeled as such. Made in
S = Small(
Catalog #WPTRS‑X Padded Tech Rescue Seat Harness(replace X w/your size)
Weight 30oz.(849g)
Catalog #WPBSH-X Padded Recreational Seat Harness(replace X w/your size)
Weight 28oz.(800g)
Weinel
Ropewalker Harness System
A state of the art, simple‑to‑use
system which allows the user to ascend a fixed line by himself. The
unique system consists of three harnesses, which when used in conjunction with
a seat harness and ascenders, will enable the wearer
to climb a rope with a minimum of effort. At the 1987 National Speleological
Society convention, Rosano Boscarino
set a new world record for climbing 100’ (27.5 seconds) and 400’ (4 minutes 10
seconds) using a homemade Ropewalker system. Of course, the average climber
will not achieve times to equal Rosano’s record, but
it does give some ideas as to the potential. The complete system consists of
the following items: one chest harness with a modified Simmons roller(Roller
with Plate, page 6), fits all chest sizes from 20”(50cm)
to 48”(121cm), one knee cam harness (one size fits all) with 6’(2m) of
.25”(7mm) shock cord and spring snap;
and one foot cam harness, one size fits all. Super
construction. All load bearing portions are made of 2”(50mm)
webbing test strength 6000 lbs.(2722kg). It is a very safe system as the
climber is attached to the rope by three independent ascenders. Barring rope or
anchor failure above the climber, it is almost impossible for the climber to
fall, as the only direction the climber can move is up. The system is available
as a complete system or as component parts‑the choice is yours. Because
the system is compatible with any seat harness, we do not supply a seat harness
with the complete system. Weight of complete system with ascenders is 8 lbs.(2.6kg), complete with harnesses only 5 lbs. 4oz.(2.4kg),
chest harness only 1 lb. 12oz. (795g), foot harness only 1 lb. 8oz.(680g). Knee
harness only 1 lb. 8oz.(680g). Made
in
Catalog #RWHCS‑1 Ropewalker Complete with Ascenders
Catalog #RWHCS‑2 Ropewalker Complete without Ascenders
Catalog #RWCH‑3 Ropewalker Chest Harness only (Includes roller and chest plate)
Catalog #RWKH‑4 Ropewalker Knee Harness only
Catalog #RWFH‑5 Ropewalker Foot Harness only (Includes link and bushing)
Catalog #RWFH-6 Ropewalker Foot Harness Floating
Weinel
Rescue Slings
Standard Rescue Sling |
Two styles and two sizes‑a rescue sling for every
need. Standard model (adult and child sizes) slips over the wearer’s head and
is adjusted to fit by way of the chest adjuster. Side opening model has a
spring closure which allows the rescuer to lay the sling flat, slip it around the
victim and then snap it shut. Quick, simple and efficient.
This style harness is favored by ski patrol and water rescue groups. Made of
9000 lb.(4082kg) 1.75”(4.5cm) webbing with 5”(12.8cm) padding, and 5000
lb.(2268kg) mil spec hardware, meets or exceeds NFPA and OSHA standards.
Standard model weight 1.5 lbs.(680g) adult, 1.25
lbs.(566g) child; side opening model 2 lbs.(907g) adult, 1.75 lbs.(794g) child.
Made in
Catalog #WRS‑1 Rescue Sling Standard Adult
Catalog #WRS‑2 Rescue Sling Side Opening Adult
Catalog #WRS‑3 Rescue Sling Standard Child
Catalog #WRS‑4 Rescue Sling Side Opening Child
Weinel
Pick-Off Strap
Weinel
Pick-Off Strap |
Adjustable length utility strap.
Often used to effect a one man pick-off. When doubled it can also be used as an anchor. Adjustable
sling from 9”(23cm) length to 54”(138.5cm) length.
Webbing is 1.75”(4.5cm) wide and 9000 lb.(4082kg).
Hardware is mil spec 5000 lbs.(2268kg). Weight 14oz.(396g). Made in
Catalog #WPOS Pick-Off Strap
Weinel
Radio Harness
A quality radio harness with your comfort
in mind. The back is made of lightweight nylon material to help you keep
your cool and it’s padded to protect your chest from the corners and edges or
the radio. This harness will hold a standard‑size, hand‑held radio
unit on the chest where it’s protected from impact and foul weather. The unique
strapping system is adjustable to a wide range of radio sizes and shapes.
Thanks to the Fastex buckles and sliders, it will
adjust to your radio in a matter of moments. Once the radio is in place, just
squeeze and talk, no need to remove the radio from the
harness. Weight 16oz.(453g). Made in
Catalog #WRH1-O Radio Harness
Catalog #WRH1-B Radio Harness Black
Yates
NFPA Full Body Harness
Yates NFPA Full Body
Harness with Optional Leg and Waist Padding |
Offers durability, comfort and strength. The design of the NFPA Harness insures a double backup of all structural webbing at the clip-in/rappel point. Unique design offers upper chest D-ring for attachment of belay line, while allowing the user to rappel from the seat portion of the harness. Yates Full Body Harness works great as a rappel training harness. Forged D-rings used for main attachment points have a proof-load strength of 5000 lbs.(2268kg) and has been tested in excess of 8000 lbs.(3629kg) without failure. NFPA Harness is constructed of Type XIII 6500 lb.(2948kg) flat webbing with quick adjustable leg loops and is sewn with contrasting color thread, offering visual inspection of all stitching. One gear rack is provided. Optional leg and waist padding is available. Harness Certification requirements were conducted by Underwriters Laboratories Inc. in accordance with the NFPA Standard for Fire Service Life Safety Harnesses (1983/1990 Edition). UL Classification 93F4. Well suited for all fire departments, heavy rescue, military, industrial and commercial applications where a Class III Harness is required. One size fully adjustable. Color: black, orange. Weight 3.5 lbs.(1.6kg).
Catalog #YNF330 NFPA Full Body Harness
Catalog #YLP330A-L 3”(7.7cm) Leg Padding
Catalog #YWP330A-W 4”(10.3cm) Waist Padding w/ D Ring
Yates
NFPA Heavy Rescue Harness
Yates NFPA Heavy Rescue
Harness |
A totally new concept in Class III harness design. The Heavy Rescue Harness has all the features needed for a Class III Fall Arrest Protection Harness. It features a rear clip-in point between the shoulders and D-rings on top of the shoulders allowing the use of a spreader bar system for industrial uses when a long hang time is anticipated. Yates Heavy Rescue Harness is designed with the rappel point of the harness at waist level. The rappel point is designed similar to the Yates Standard NFPA Class II Harness. This new concept in full body harness design combines the Fall Arrest Protection needed in a Class III harness and the comfort of a waist level rappel point. Yates Heavy Rescue Harness is designed for durability, comfort and strength. Harness Certification requirements were conducted by Underwriters Laboratories Inc. in accordance with the NFPA Standard for Fire Service Life Safety Harnesses (1983/1990 Edition). UL Classification 93F4. Forged D-rings used for main attachment points have a proof-load strength of 5000 lbs.(2268kg) and have been tested in excess of 8000 lbs.(3629kg) without failure. Yates Heavy Rescue Harness is well suited for all fire departments, heavy rescue, military, industrial and commercial applications where a Class III harness is required. One size fully adjustable. Color: black, orange. Weight 4.2 lbs.(1.9kg). Available with optional waist and leg pads.
Catalog #YHR335 NFPA Heavy Rescue Harness
Catalog #YHR340 NFPA Heavy Rescue Harness w/ waist and leg pads
Yates
NFPA Rescue Harness
Yates NFPA Rescue Harness |
Offers durability, comfort and strength. The Rescue Harness is well suited for rescue, military or SWAT applications where a metal attachment point is not necessary. The Yates Rescue Harness was originally designed for the U.S. Navy Seals tactical teams. The anatomical configuration of the harness has made it the choice for many tactical teams who need a non-restrictive harness system. Front attachment point is provided through reinforced rolled 2”(5.13cm) webbing. The leg loops are “quick” adjustable, using Mil-Spec. hardware. Two gear racks are provided. All buckles are epoxy coated with a matte-black finish to reduce reflective light for tactical operations. Harness certification requirements were conducted by Underwriters Laboratories Inc. in accordance ANSI A10.14. One size fully adjustable. Color: solid black. Weight 1.7 lbs.(.77kg).
Catalog #YRH320 NFPA Rescue Harness
Catalog #YRH320A NFPA Rescue Harness with Padding
Yates
NFPA Chest Harness
Yates NFPA Chest Harness |
Excellent for water rescue personnel. Universal fit allows the harness to easily fit over water rescue suits. Front clip-in forged D-ring has a proof-load of 5000 lbs.(2268kg). All hardware is epoxy coated with a matte-black finish for corrosion resistance. The NFPA Chest Harness is constructed of Type XIII 6500 lb.(2948kg) flat webbing and is sewn with contrasting color thread. Double pass buckle ensures that the webbing will not slip when properly fastened. Harness Certification requirements were conducted by Underwriters Laboratories Inc. in accordance with the NFPA Standard for Fire Service Life Safety Harnesses (1983/1990 Edition). UL Classification 93F4. One size fully adjustable. Orange or Black Weight 1.4 lbs.(.6kg).
Catalog #YCH425 NFPA Chest Harness
Yates
Pick-Off Strap
Adjusts to a maximum length of eight feet(2.4m). The Pick-Off Strap is a multi-functional tool. It can be used to secure a victim to a rescuer or to a litter. It can be used as an adjustable daisy chain for the litter attendant or used as an adjustable hard point attachment. Available in 1:1 Standard Pick-off or 2:1 Heavy Duty Pick-off Strength: 5000 lbs.(2268kg). Color: orange. Weight 1 lb.(.5kg).
Catalog #YPOS439 Standard Pick-Off Strap
Catalog #YPOS440 Heavy Duty Pick-Off Strap
Yates
Rescue Harness
Well suited for rescue, military, SWAT and tactical rappel applications where a metal attachment point is not necessary. Originally designed for the US Navy Seals tactical teams, the anatomical configuration of the harness has made it the choice for many tactical teams who need a non-restrictive harness system. Front attachment point is provided through slot webbing construction. One size and fully adjustable. Quick leg adjustment with camlock buckles. All hardware are plated or epoxy coated black. One gear rack. Meets ANSI/OSHA Class II harness standards.
Catalog #YRH310 Rescue Harness
Yates
Rescue Chest Harness
Basic chest harness with V ring attachment points that can be connected together with carabiner or rope. Comes with special O ring strap that provides a rigging point and connects the V ring. One size and fully adjustable.
Catalog #YRCH415 Rescue Chest Harness
Yates
Victim Rescue Seat Harness
Yates Victim Rescue Seat Harness |
Lightweight harness specially designed for victim rescue. Double locking quick connect snap hook and locking D ring adjustment system allows for fast application on a victim. Waist pocket securely holds legs straps while rescue applies belt to victim giving the rescuer a fast clip in point. Leg straps are then removed and applied. Waist and leg portions of harness are color coded using orange, blue and black webbing to assist the rescuer application. Leg buckles are also color coded and are quickly adjustable when on victim. One size and fully adjustable. Large D ring for multiple connections. Waist pad under buckle for added comfort. Meets ANSI/OSHA Class II standards.
Catalog #YVRS321 Victim Rescue Seat Harness
Yates
SAR Harness
Lightweight harness designed specifically for search and
rescue professionals. Unique waist
pocket provides ability to be worn as a belt and quickly converted into a Class
II seat harness. Utilizes
a double pass waist buckle and forged two piece friction buckles on the legs. Main attachment point allows freedom of
movement with reduced bulk. Sizes S, M,
L, XL, XXL (by special order). Will accept military
Catalog #YSAR312 SAR Harness
Yates
Assault Seat Harness
Yates Assault Seat Harness
with Optional Leg and Waist Padding |
Offers durability, comfort and strength. The design of the Assault Harness insures a double backup of all structural webbing at the clip-in/rappel point. Forged D-ring used for the main attachment point has a proof-load strength of 5000 lbs.(2268kg) and has been tested in excess of 8000 lbs.(3629kg) without failure. The Assault Harness is constructed of Type XIII 6500 lb.(2948kg) flat webbing with quick adjustable leg loops. All buckles are Epoxy coated with a matte-black finish to reduce reflective light for tactical operations. One gear rack is provided. Optional leg and waist padding is available. Harness Certification requirements were conducted by Underwriters Laboratories Inc. in accordance with the NFPA Standard for Fire Service Life Safety Harnesses (1983/1990 Edition). UL Classification 93F4. Yates Assault Harness is well suited for all rescue, military, SWAT and tactical applications where a Class II Harness is required. One size fully adjustable. Color: solid black. Weight 2 lbs.(.9kg).
Catalog #YAS315 Assault Seat Harness
Catalog #YLP316A 3”(7.7cm) Leg Padding
Catalog #YWP316B 4”(10.3cm) Waist Padding w/ D Ring
Yates
Extraction Harness
Same as the Heavy Rescue Harness except all buckles are Epoxy coated with a matte-black finish to reduce reflective light for tactical operations. The Extraction Harness is well suited for all rescue, military, SWAT, and tactical applications where a Class III Harness is required. One size fully adjustable. Color: solid black. Weight 4.2 lbs.(1.9kg).
Catalog #YEH355 Extraction Harness
Yates
Last Chance Belt
A uniform rappel
belt. Made of 1.75”(4.5cm) black webbing with a
test strength of 9000 lbs.(4090kg). Double pass buckle ensures that the webbing
will not slip when properly fastened. One size fits all up to 52”(133cm). Features a sewn in V ring near the buckle. For an
emergency escape, simply flip open the V ring, clip in a carabiner
and a rappel device then make your descent. Looks great on your uniform and you
will be sure to always have it with you. Color: black with black hardware.
Weight 8oz.(229g). Made in
WARNING: this item is sold as a belt. It is not to be used for rappelling except under direct threat to your life.
Catalog #YLCB450 Last Chance Belt Regular
Catalog #YLCB451 Las Chance Belt Extra Large
Lirakis
Fagan Full Body Harness
Fagan Full Body Harness |
One size fits all. This harness
is made of 2”(5cm), 9000 lb.(4082kg) test minimum
strength webbing. All the hardware is to military specifications. This harness
is uniquely comfortable and simple. The leg, waist and shoulder straps are
individually adjustable. There is a D-ring high on the back for lifting or
restraining while keeping you in an upright position. Another D-ring in front
at the waist is positioned for rappelling or as another lifting point. Color:
blue and red. Weight 4.5 lbs.(2kg). Made
in
Catalog #FFB2 Fagan Full Body Harness
Lirakis
Killington Full Body Harness
Killington Full Body
Harness |
This harness which is light, strong and simple offers
ultimate protection, distributing load over the wearer’s entire frame. It is
made entirely of 2”(5cm) nylon webbing with a 9000
lb.(4082kg) minimum breaking strength. All hardware is stainless steel. D-rings
for lifting may be added at the shoulders or at the middle of the back. Color:
Blue. Weight 1.8 lbs.(.8kg). Made in
Size |
Waist |
Small |
34”-45”(87-115cm) |
Large |
41”-58”(105-149cm) |
Catalog #KFB1 Killington Full Body Harness
Lirakis
Rappel Seat Harness
Rappel Seat
Harness |
One size fits all, easy to put on, easy to adjust, and long
wearing. This seat was designed with tactical exercises in mind, however it has
been found to be outstanding for rescue work, far superior to the traditional
Swiss seat for comfort and versatility. The harness is constructed entirely of
2”(5cm) nylon webbing of 9000 lb.(4082kg) minimum
strength. The waist and leg straps are individually adjustable; and all
hardware is to military specification. This harness is secured to your body by
one snap. Three adjustments snug it comfortably to your body, making inspection
easy. To properly secure the harness to your body snug the waist strap first
then each leg strap. Colors: blue, black. Weight 26oz.(736g).
Made in
Catalog #BC3-1 Rappel Seat Harness
Catalog #BC3-2 Rappel Seat Harness, Tactical Black
Miller
Wristlets
Miller #6400N Wristlets |
Miller #6255 Wristlets |
Two models.
OSHA allows Wristlets to be used whenever a harness would be impractical or
would create a greater hazard. Wristlets are used mainly in areas with
extremely narrow openings or in glass or other easily damaged tanks. Wristlets
are for retrieval only, do not use for fall protection. The Miller #6400N
Wristlets are made from soft nylon webbing with leather padding and weigh 3.3oz.(94g) each. The Miller #6255 Wristlets are made from soft
comfortable leather with adjustable buckles and weigh 5.7oz.(163g)
each. Sold in pairs. Made in
Catalog #6400N Miller Wristlets, Nylon
Catalog #6255 Miller Wristlets, Leather
Bashlin
Wrist Harness
Bashlin Wrist Harness |
Wrist Harnesses are intended to
be used as a retrieval device only, and must not be used for fall protection or
as a lifting device. They are intended to guide hands and wrists to allow
retrieval utilizing a rated harness or other suitable rescue device. Wrist
Harnesses are for emergency work and for work locations where a full body
harness might not be practical due to close quarters or small openings. Made of
1”(2.5cm) nylon webbing with cushioning material
around wrist, it grips the wrist with a choker style hitch. They can be
fastened into place while performing work. During emergency lifting or
dragging, the hitch snugs around the wrist enabling
rescue work to be performed in confined spaces without complicated rescue
devices. Weight 1 lb.(.45kg). Made
in
Catalog #696-NW Wrist Harness
Bashlin
Tree Trimming Saddle
Tree Trimming Saddles are
designed to give not only service but comfort. They are designed to take the
place of old style rope saddles that cut and burn the user’s legs and hips. The
Size |
Waist |
Small |
34”-42”(87-108cm) |
Medium |
37”-45”(95-115cm) |
Large |
41”-49”(105-126cm) |
X-Large |
44”-52”(113-133cm) |
Catalog #669-SIZE Tree Trimming Saddle
Bashlin
Pole/Tree Climbers
Adjustable climbers with a
replaceable gaff made of high strength aluminum alloy. They are lighter than steel
climbers, but have the same strength as steel models. This is a deluxe climber,
lightweight and very comfortable. Standard sleeves can be adjusted from 15”(38cm) to 18”(45.7cm) in 1/4”(6mm) steps. This assures a
perfect fit for utmost comfort. One pair of Climbers consists of left and right
leg straps and leg pads. Note: Bashlin makes many
other styles of Climbers (including steel) and offers a wide range of options.
Call us to discuss your special needs. Weight 5 lbs.(2.27kg)
per pair. Made in
Catalog #BD-14-4 Tree Climber Set
Catalog #BD-14T-4 Tree
Climber Set
Conterra
Radio Chest Harness
Radio Chest
Harness |
This one-size-fits-all Radio Harness will instantly adjust to fit any handheld radio. Holds snugly to your chest, without the need for multiple Velcro straps or buckles. Features all-Cordura construction; a large capacity, bellows cargo pouch; pen pouch; and twin elastic antenna keepers. A must for SAR applications.
Catalog #94RCH-1 Conterra Radio Chest Harness